May 22, 2025Leave a message

How to store a submersible well pump during the off - season?

Hey there! As a supplier of Submersible Well Pumps, I've seen firsthand how important it is to store these pumps properly during the off - season. If you don't take the right steps, you could end up with a pump that's damaged or doesn't work as well when you need it again. So, let's dive into how you can store your submersible well pump correctly.

1. Pre - storage Inspection

Before you even think about storing your pump, you've got to give it a good once - over. First off, check the exterior for any signs of damage, like cracks or dents. These can let water in and cause all sorts of problems down the line. If you find any damage, it's best to get it fixed before storage.

Next, look at the electrical connections. Make sure they're tight and free from corrosion. Loose or corroded connections can lead to electrical issues later. You can use a wire brush to clean off any corrosion you find on the terminals.

Also, take a look at the impeller. The impeller is a crucial part of the pump that moves the water. If it's clogged with debris or has any signs of wear, you should clean or replace it. You can usually access the impeller by removing a few screws on the pump housing.

2. Cleaning the Pump

Cleaning your submersible well pump is a must. Start by disconnecting the pump from the power source. This is super important for your safety. Then, remove the pump from the well.

Once you've got the pump out, rinse it thoroughly with clean water. You want to get rid of any dirt, mud, or other debris that might be stuck to it. Pay special attention to the intake screen. This screen keeps big particles from getting into the pump, and if it's clogged, it can reduce the pump's efficiency. You can use a soft brush to gently scrub the screen and remove any stubborn debris.

42

After rinsing, you can use a mild detergent to clean the pump further. Just make sure the detergent is safe for use on the pump's materials. Rinse it again to remove all the detergent.

3. Draining the Pump

Draining the pump is key to preventing damage from freezing. If water is left inside the pump during cold weather, it can freeze and expand, cracking the pump housing or other components.

To drain the pump, look for any drain plugs or valves. These are usually located at the bottom of the pump or on the sides. Open them up and let all the water drain out completely. You might need to tilt the pump a bit to get all the water out.

If your pump has a built - in check valve, you may need to take some extra steps to ensure proper draining. Sometimes, water can get trapped on the other side of the check valve. You may need to consult the pump's manual or contact the manufacturer for specific instructions on draining with a check valve.

4. Lubrication

Lubricating the moving parts of your pump can help prevent rust and keep the pump in good working condition during storage. Check the pump's manual to see what type of lubricant is recommended.

Use a small amount of lubricant on the bearings, seals, and any other moving parts. Be careful not to over - lubricate, as too much lubricant can attract dirt and debris. You can use a clean cloth or a small brush to apply the lubricant evenly.

5. Storage Location

Finding the right place to store your submersible well pump is crucial. You want a dry, clean, and temperature - controlled environment. A basement or a shed can work well, as long as it's not prone to flooding or extreme temperature changes.

Avoid storing the pump in direct sunlight or in a place where it can get wet. Moisture can cause rust and corrosion, which can damage the pump. Also, make sure the storage area is well - ventilated to prevent the buildup of any harmful fumes.

If you're storing multiple pumps, make sure they're not stacked on top of each other. This can cause damage to the pumps, especially if there's any pressure on them.

6. Protection

To give your pump some extra protection during storage, you can cover it with a protective cover. You can buy a cover specifically designed for submersible well pumps, or you can use a tarp or a plastic sheet.

Make sure the cover fits snugly and is secured well. This will keep dust, dirt, and moisture away from the pump. You can also use a desiccant pack inside the cover to absorb any excess moisture.

7. Regular Checks

Even though your pump is in storage, it's a good idea to check on it regularly. Every few months, take a look at the pump to make sure there are no signs of damage, rust, or corrosion.

If you notice any issues, address them right away. For example, if you see a little bit of rust starting to form, you can use a rust remover and then re - lubricate the affected area.

Why Proper Storage Matters

Proper storage of your submersible well pump can save you a lot of money and hassle in the long run. A well - stored pump will last longer and perform better when you need it again. It can also prevent costly repairs or the need to replace the pump prematurely.

If you're in the market for a new submersible well pump or other related pumps, we've got you covered. We offer a wide range of pumps, including Agricultural Irrigation Water Pump and Submersible Bore Pump. Our Submersible Well Pump is of high quality and built to last.

If you have any questions about our pumps or need more information on pump storage, don't hesitate to reach out. We're here to help you make the right choice for your needs. Whether you're a farmer looking for an irrigation pump or a homeowner in need of a well pump, we can assist you.

So, if you're interested in purchasing a pump or just want to talk about your options, feel free to contact us for a chat. We're always happy to have a friendly conversation and help you find the perfect pump for your situation.

References

  • Manufacturer's manuals for submersible well pumps
  • Industry best practices for pump maintenance and storage

Send Inquiry

whatsapp

Phone

E-mail

Inquiry